无线渗透技术概念 无线

admin 8月前 119

  root@kali:~# iw list

  Wiphy phy0

  max # scan SSIDs: 4

  max scan IEs length: 2257 bytes

  max # sched scan SSIDs: 0

  max # match sets: 0

  max # scan plans: 1

  max scan plan interval: -1

  max scan plan iterations: 0

  Retry short long limit: 2

  Coverage class: 0 (up to 0m)

  Device supports RSN-IBSS.

  Supported Ciphers:

  * WEP40 (00-0f-ac:1)

  * WEP104 (00-0f-ac:5)

  * TKIP (00-0f-ac:2)

  * CCMP-128 (00-0f-ac:4)

  * CCMP-256 (00-0f-ac:10)

  * GCMP-128 (00-0f-ac:8)

  * GCMP-256 (00-0f-ac:9)

  Available Antennas: TX 0 RX 0

  Supported interface modes:

  * IBSS

  * managed

  * AP

  * AP/VLAN

  * monitor

  * mesh point

  Band 1:

  Capabilities: 0x17e

  HT20/HT40

  SM Power Save disabled

  RX Greenfield

  RX HT20 SGI

  RX HT40 SGI

  RX STBC 1-stream

  Max AMSDU length: 3839 bytes

  No DSSS/CCK HT40

  Maximum RX AMPDU length 32767 bytes (exponent: 0x002)

  Minimum RX AMPDU time spacing: 2 usec (0x04)

  HT TX/RX MCS rate indexes supported: 0-7, 32

  Bitrates (non-HT):

  * 1.0 Mbps

  * 2.0 Mbps (short preamble supported)

  * 5.5 Mbps (short preamble supported)

  * 11.0 Mbps (short preamble supported)

  * 6.0 Mbps

  * 9.0 Mbps

  * 12.0 Mbps

  * 18.0 Mbps

  * 24.0 Mbps

  * 36.0 Mbps

  * 48.0 Mbps

  * 54.0 Mbps

  Frequencies:

  * 2412 MHz [1] (20.0 dBm)

  * 2417 MHz [2] (20.0 dBm)

  * 2422 MHz [3] (20.0 dBm)

  * 2427 MHz [4] (20.0 dBm)

  * 2432 MHz [5] (20.0 dBm)

  * 2437 MHz [6] (20.0 dBm)

  * 2442 MHz [7] (20.0 dBm)

  * 2447 MHz [8] (20.0 dBm)

  * 2452 MHz [9] (20.0 dBm)

  * 2457 MHz [10] (20.0 dBm)

  * 2462 MHz [11] (20.0 dBm)

  * 2467 MHz [12] (20.0 dBm) (no IR)

  * 2472 MHz [13] (20.0 dBm) (no IR)

  * 2484 MHz [14] (20.0 dBm) (no IR)

  Supported commands:

  * new_interface

  * set_interface

  * new_key

  * start_ap

  * new_station

  * new_mpath

  * set_mesh_config

  * set_bss

  * authenticate

  * associate

  * deauthenticate

  * disassociate

  * join_ibss

  * join_mesh

  * set_tx_bitrate_mask

  * frame

  * frame_wait_cancel

  * set_wiphy_netns

  * set_channel

  * set_wds_peer

  * probe_client

  * set_noack_map

  * register_beacons

  * start_p2p_device

  * set_mcast_rate

  * connect

  * disconnect

  * set_qos_map

  * Unknown command (121)

  Supported TX frame types:

  * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0

  * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0

  * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0

  * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0

  * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0

  * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0

  * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0

  * P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0

  Supported RX frame types:

  * IBSS: 0x40 0xb0 0xc0 0xd0

  * managed: 0x40 0xd0

  * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0

  * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0

  * mesh point: 0xb0 0xc0 0xd0

  * P2P-client: 0x40 0xd0

  * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0

  * P2P-device: 0x40 0xd0

  software interface modes (can always be added):

  * AP/VLAN

  * monitor

  valid interface combinations:

  * #{ AP, mesh point } <=8,< p="">

  total <=8, #channels <=1< p="">

  HT Capability overrides:

  * MCS: ff ff ff ff ff ff ff ff ff ff

  * maximum A-MSDU length

  * supported channel width

  * short GI for 40 MHz

  * max A-MPDU length exponent

  * min MPDU start spacing

  Device supports TX status socket option.

  Device supports HT-IBSS.

  Device supports SAE with AUTHENTICATE command

  Device supports low priority scan.

  Device supports scan flush.

  Device supports AP scan.

  Device supports per-vif TX power setting

  Driver supports full state transitions for AP/GO clients

  Driver supports a userspace MPM

  Device supports configuring vdev MAC-addr on create.

  文章来源:http://www.cnblogs.com/ethtool/p/12187394.html%20


少客联盟- 版权声明 1、本主题所有言论和图片纯属会员个人意见,与少客联盟立场无关。
2、本站所有主题由该帖子作者发表,该帖子作者admin少客联盟享有帖子相关版权。
3、少客联盟管理员和版主有权不事先通知发贴者而删除本文。
4、其他单位或个人使用、转载或引用本文时必须同时征得该帖子作者admin少客联盟的同意。
5、帖子作者须承担一切因本文发表而直接或间接导致的民事或刑事法律责任。
6、本帖部分内容转载自其它媒体,但并不代表本站赞同其观点和对其真实性负责。
7、如本帖侵犯到任何版权问题,请立即告知本站,本站将及时予与删除并致以最深的歉意。
8、官方反馈邮箱:chinasuc@chinasuc.cn


上一篇:PowerShell渗透工具Nishang的用法
下一篇:Linux 权限提升--SUID
Whatever is worth doing is worth doing well. juvenile hacker league
最新回复 (0)
    • 少客联盟
      2
        登录 注册 QQ登录(停用)
返回